Beyond that, you will also want to check all the power window switches in the car. If the master switch is not working on the driver’s side door panel, but all the others are, it may be isolated to one switch. If several switches are not working for one particular window, the window regulator assembly could be to blame rather than the switch.
2011 Mazda3i, 4-door. Door Lock issues. FYI I do not have a remote key fob. 1) All doors will lock when in drive. 2) All doors will unlock/lock using the key on the driver’s door, but not when using the key in the passenger door. 3) The lock/unlock buttons on both front doors do not work. Advertisements. In this article, we consider the second-generation Mazda 3 (BL), produced from 2010 to 2013. Here you will find fuse box diagrams of Mazda3 2010, 2011, 2012 and 2013, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout). See other Mazda 3:
However, if you disconnect the motor from the frame and let it dangle on the regulator wires, you can pull it all the way through to the other port in the frame. That way, it turns out that, it was even easier to work with than the driver window motor. Hope this helps. Posted on Jun 25, 2010.
Welcome to FixYa. You will need to check all connections in door. Make sure to have a 12 volt test light, remove door panel and check window switch for power if ok go to motor hold test light to the hot wire to motor, use window switch does test light light up if so motor is bad. Step 3: Inspect cables. Visually inspect cables or guides for broken or misaligned pieces. If you see a loose or broken cable and hear the motor moving when activated, then the window regulator would need to be replaced. Step 4: Check for stripped gears. If nothing is found, remove motor from regulator to check for stripped gears.
3. Power Window Motor. Your Saab 9-3’s power window motors can and do fail over time. You’ll have to take the door panel off to get to it. A lot of them are riveted in, so be prepared to deal with that. If you’ve verified that it is getting power with a voltmeter, but it is not working, it’s time to get a new one.
4. Pull window switch up to fully close door window; hold switch up for two (2) seconds; release switch. 5. Move to front passenger seat and repeat Steps 3 - 4 on passenger window switch. 6. Mazdaspeed6 Only: Move to rear seat and repeat Steps 3 - 4 at left and right rear seat window switches. 7. Verify proper window operation using each door First, turn on the car or set the ignition switch to the accessory position. Next, open the door and sandwich the window between your hands. Position your hands so each palm is as flat as possible on each side of the glass. While doing this, have another person engage the power window button to raise the window. 7nJRC.
  • 86qeemwjiq.pages.dev/227
  • 86qeemwjiq.pages.dev/590
  • 86qeemwjiq.pages.dev/699
  • 86qeemwjiq.pages.dev/929
  • 86qeemwjiq.pages.dev/872
  • 86qeemwjiq.pages.dev/125
  • 86qeemwjiq.pages.dev/33
  • 86qeemwjiq.pages.dev/113
  • 86qeemwjiq.pages.dev/388
  • 86qeemwjiq.pages.dev/318
  • 86qeemwjiq.pages.dev/92
  • 86qeemwjiq.pages.dev/629
  • 86qeemwjiq.pages.dev/730
  • 86qeemwjiq.pages.dev/76
  • 86qeemwjiq.pages.dev/275

    • mazda 3 rear power window not working